« previous next »
Pages: [1] 2

Author Topic: Enfield mods  (Read 1140 times)

Propellor

  • Full Member
  • ***
  • Posts: 1259
Enfield mods
« on: October 16, 2018, 08:54:50 PM »
Started a few mods. Here's one.

[attachment deleted by admin]
Logged
BEIGE is all the rage

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #1 on: October 16, 2018, 08:55:56 PM »
Started off

[attachment deleted by admin]
Logged
BEIGE is all the rage

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #2 on: October 16, 2018, 08:56:28 PM »
Then

[attachment deleted by admin]
Logged
BEIGE is all the rage

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #3 on: October 16, 2018, 08:56:55 PM »
Finally!

[attachment deleted by admin]
Logged
BEIGE is all the rage

Smithy

  • Posts: 827
Re: Enfield mods
« Reply #4 on: October 17, 2018, 06:21:17 AM »
Andy that is so neat and tidy. You should think about going into production I bet there would be a market for that kind of minimal light fitting.

Ian
Logged

Moto63

  • Full Member
  • ***
  • Posts: 4176
Re: Enfield mods
« Reply #5 on: October 17, 2018, 06:43:04 AM »
Looking good 👍
Logged

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #6 on: October 18, 2018, 05:36:05 AM »
Cheers chaps.

Moving to the next step of my rear end makeover. I want to keep the same rear mudguard but rotate it forwards so that it doesn't drape so far down at the back. Also change the tubular brace for an ally one akin to the brace seen on '60's Harley sportsters.

Had real bother getting the mudguard free from the brace. Got 4 of the 6 screws out on a wing and a prayer. Two I had to grind/drill out. Next hurdles are the reg/rec, which is mounted to the back of the l/h toolbox, will have to be re sited and the pathetic rubber snout on the back of the r/h box also fouls. That I was going to re make anyhow as it's clearly an afterthought.
Logged
BEIGE is all the rage

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #7 on: October 18, 2018, 11:30:05 AM »
Anyone know if a blanking plug (plate) is available to blank off the starter motor hole? A section drawing shows a spigot with an o ring on the motor. I'm wantng  to remove the motor permanently. Making one in a vice would be difficult (Not impossible!). Otherwise I'd have one machined up.
Logged
BEIGE is all the rage

Smithy

  • Posts: 827
Re: Enfield mods
« Reply #8 on: October 18, 2018, 05:01:08 PM »
Hitchcocks do one for about a tenner.

Ian
Logged

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #9 on: October 18, 2018, 05:47:31 PM »
Thanks Ian.

This seems to be it.

http://accessories.hitch*******smotorcycles.com/accessory-shop/crankshaft-engine/21512

Edit: you need to complete the naughty bit in the link, which the over zealous filter on here has deleted. 😂😂😂😂😂😂😂
« Last Edit: October 18, 2018, 05:50:20 PM by Propellor »
Logged
BEIGE is all the rage

Smithy

  • Posts: 827
Re: Enfield mods
« Reply #10 on: October 19, 2018, 07:20:14 AM »
It certainly is a very prudish filter. I wonder what would happen if Hitch*******s were based in S*******horpe?

Ian

Well now we know!
Logged

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #11 on: October 19, 2018, 09:45:46 AM »
😂😂😂😂😂😂😂😂

All hell would be let loose.
Logged
BEIGE is all the rage

Moto63

  • Full Member
  • ***
  • Posts: 4176
Re: Enfield mods
« Reply #12 on: October 19, 2018, 03:29:01 PM »
Ha ha ha ha ha.... good one Ian
Logged

Moto63

  • Full Member
  • ***
  • Posts: 4176
Re: Enfield mods
« Reply #13 on: October 19, 2018, 04:13:22 PM »
Been thinking maybe it shud now be know as hitchknobs, or hitchwillys......or why not hitchdicks🤣🤣🤣🤣
Logged

Propellor

  • Full Member
  • ***
  • Posts: 1259
Re: Enfield mods
« Reply #14 on: October 19, 2018, 04:58:51 PM »
Hitchmember
Logged
BEIGE is all the rage
Pages: [1] 2
« previous next »