Thumper Club Forum

Club House => Chatter => Topic started by: guest27 on June 20, 2009, 08:04:38 PM

Title: Honda flywheel puller D
Post by: guest27 on June 20, 2009, 08:04:38 PM

Hi does anyone have the Honda Flywheel Puller D or a pattern part I can borrow - part No 079330010000

Dave Silver does have them - on special order - but will take over a week to get in.

It is for a CG125 but I would guess it fits many of the smaller Hondas.  I may even have one myself - but if I do who knows where it is.  There is no room for a 3-leg puller, this thingy is about 22mm OD thread and a threaded 'bolt' through that.

R

Title: Re: Honda flywheel puller D
Post by: squirrelciv on June 21, 2009, 08:35:12 AM

Haven't sorry Rog, but when I needed the flywheel off Abigail I just popped the motor down to the local bike garage and slipped the guy a £5. Job done in under a minute.

Title: Re: Honda flywheel puller D
Post by: guest146 on June 21, 2009, 07:53:45 PM

If you have access to or know an HGV fitter, the HGV wheel studs that are on 90% of heavy trucks are the same thread. Just wind it in and tap the pulley and off it comes. Fits the Dommi I know that for sure.

Ken

Title: Re: Honda flywheel puller D
Post by: guest27 on June 21, 2009, 08:20:56 PM

Thanks to both of you

Will liberate a wheel bolt off the next HGV that parks on the zig-zags outside the school...  ;D

R

Title: Re: Honda flywheel puller D
Post by: KirriePete on June 21, 2009, 10:08:08 PM

Is it the same one as the C50/70/90 ?  Lefthand thread on the outer IIRC.  If so, I've got one buried in the Shed that currently has no purpose in life and would probably welcome some action.

Title: Re: Honda flywheel puller D
Post by: guest27 on June 22, 2009, 08:55:24 AM

Not sure if it is the same one - but my guess would be yes.  Any chance of a borrow?

R

Title: Re: Honda flywheel puller D
Post by: KirriePete on June 22, 2009, 08:58:49 AM

Quote from: Rog on June 22, 2009, 08:55:24 AM

Not sure if it is the same one - but my guess would be yes.  Any chance of a borrow?

R

I'll have a rummage in the shed tonight, post up a piccy so you can check then PM me with delivery requirements. 

Title: Re: Honda flywheel puller D
Post by: guest564 on June 23, 2009, 05:59:54 PM

You can quite often use the rear wheel spindle.

Title: Re: Honda flywheel puller D
Post by: guest27 on June 23, 2009, 07:22:52 PM

Most often to hold the rear wheel in...  ;D

I had thought that as I was pulling the cases off - but the rear spindle is 10mm or 12mm and the hole is 22mm or there abouts but a good thought.

R

Title: Re: Honda flywheel puller D
Post by: blew on June 23, 2009, 09:44:08 PM

I have a puller that fits small Hondas-50/70/90 etc..Where are you?

Title: Re: Honda flywheel puller D
Post by: crackedhead on June 23, 2009, 09:57:09 PM

lings.com show that item is available, at £6.24, for next day dispatch.

Good luck

Title: Re: Honda flywheel puller D
Post by: guest27 on June 24, 2009, 08:27:19 AM

Quote from: blew on June 23, 2009, 09:44:08 PM

I have a puller that fits small Hondas-50/70/90 etc..Where are you?

Hi Blew

I am in Cwmafan / Port Talbot.  Thanks, however Kirriepete is sending me one that is clutter in his shed.

R

Title: Re: Honda flywheel puller D
Post by: blew on June 24, 2009, 09:16:56 AM

I'm quite close.If you want it today,ring me on 07761330285

Title: Re: Honda flywheel puller D
Post by: guest27 on June 25, 2009, 11:51:23 AM

Hi Blew

Thanks - was wall to wall with kids last night - boss in meeting till 9:30ish so did not have a chance to call.  Pete's turned up this am in the post.

Where abouts are you?

R